SaniStride offers the only modular shoe sanitizer runner mats in existance

Stride LONG 1/2″ LOW PROFILE (LP) Runner pieces

$254.00

Enter/Exit & Center Sections | Modular Shoe Sanitizing Mat System

EACH RUBBER BASE MAT W/INSERT INCLUDED IS $254. It takes 2 sections at $254 each to create the minimum size Runner Shoe Disinfection Station. 1-18″ SaniClip comes with each 2 End Long Runner sections ordered… additional Clips added for center sections. Sanitizer not included.

1/2 inch thick double sided insert included, 4 inch wide surround ramps & 1/2 inch total mat height

18″ Wide Wet Surface Enter/Exit & Center | Modular Sanitizing Mat System

The minimum size LONG shoe sanitizer runner must consist of at least 2-end, enter/exit ramp sections at $254 each section… as in the 2 piece image to the left. Add center units to construct the LONG modular system to your desired length. Add an additional 2 end ramp sections per each additional location you want to place 1- 2 piece (or more) LONG LP system.

Quality American Craftsmanship | Sanitizer Mats

Each base-mat section comes with a blue/black marbled double sided carpet 1/2″ thick insert, with your choice of red, yellow or blue trim as seen in the product images to the left.

If you need assistance with configuring your LP LONG Runner, please call 888.302.4857 (10am-3pm M-F Pacific) and we will assist you.

Fulfillment is 2-3 days – ships UPS ground from the state of WA.

Note: Sanitizer solution not included – SaniStride does not sell or distribute sanitizers. Please see the Setup and Maintenance page for recommendations on sanitizer usage. And be sure to question your chemical supplier regarding the efficacy of the sanitizer you are using.

Clear
SKU: N/A Categories: , ,

Description

Please see the Stride LOW PROFILE (LP) Mat System 1/2″ deep product page for more info on the LP Modular Mat.

We suggest charging each LP insert in the Runner System with 108-114 fluid ounces maximum of sanitizer.

Modular Sanitary Mat System

LIMITED INVENTORY on the 1/2 inch deep LOW PRO LONG Shoe Sanitizer Runner components… some delays in fulfillment could be encountered. We will inform you immediately if there is a several day delay for LP Long production upon receiving your order.

Each base-mat piece of the 1/2 inch deep LOW PRO LONG Runner System is $254, insert included as well as hook and loop strips for holding sections together (1 additional loop strip per strut also included).

Built-to-Fit Sanitizer Mat

The LP Long Runner is a modular mat system to create a LONG and wide Shoe Sanitizer Runner. The minimum size LONG runner consists of 2-end ramp sections with a 1″ wide, 1/2″ high strut between the 2 sections, held together with our new Sani-Clip, which has replaced the previous hook and loop system. The wet sanitizer surface is 2-sections of 34″L x 18″W, total 68″L x 18”W wet surface. The ramp around the merged sections is 4″ wide. The outer dimension of the 2-piece long is 78″L x 27″W. One inch is added in length for each strut you create by adding center sections to your LP runner configuration.

By adding LONG CENTER sections L34″ x W18″ wet area, you can create a LP Long runner as long as desired… each additional section creates another 1″ wide 1/2″ high center strut. An additional Sani-Clip is provided for each additional center section added.

The 1/2″ thick Low Profile insert is a Sanistride® proprietary design. We suggest charging each LP insert with 108-114 fluid ounces maximum of sanitizer.

The 1/2″ thick Low Profile insert is a Sanistride® proprietary design. We suggest charging each LP insert with 108-114 fluid ounces maximum of sanitizer.

Simple Sanitizer Mat Clean Up

Sanistride® mats have an easy clean-out protocol: Simply flush/rinse the insert and base-mat with clean water in a utility sink or with a hose. Stand or hang the insert on-end to drain the water quickly and drip dry overnight. If you desire to use the System 24/7, you will want to order a replacement insert with your initial order… it is needed for the cleaning rotation process as one will need to drip dry overnight. Please see the Setup and Maintenance page for more info.

(Please note: DO NOT put the insert in the EXTRACTOR, WASHER or DRYER as this will destroy the insert and its inner material.)

Related products